R80 COLD ROLLING MILLS FOR RIDGE CAP WITH RIBS
This Profile Drawing As Below Picture:
Profile:YX15-96
YX15-145
Material: 0.30mm Minimum Thickness, 0.6mm Maximum Thickness
Feeding width: 152MM/203MM
Galvanized Coil/Zincalume-Galvaume Coated,Pre-paint Coil;
Yield Strength: 250Mpa
General Parameter
| 1 |
Item |
Parameters |
| 2 |
Model NO. |
YX15-96/145 |
| 3 |
Material |
Pre-painted galvanized sheet |
| 4 |
Thickness |
0.3-0.6mm |
| 5 |
Yield Strength |
250 MPa |
| 6 |
Feed Width |
1250 mm |
| 7 |
Effective width |
|
| 8 |
Roll Stages |
18 Stages |
| 9 |
Shafts Diameter |
75 mm |
| 10 |
Main Motor Power |
|
| 11 |
Hydraulic Group Power |
11kw |
| 12 |
Max. Line Speed Of Roll Former |
3-4m/min |
| 13 |
Electric Standard |
|
Machine Components
A. 3TonX300mm Hydraulic Un-Coiler (powered drive)
Load capacity= MAX.1.5Ton; Coil Width= MAX. 300mm
Coil inner-diameter=400-580mm, outside-diameter Max. 1600mm
Retarding Motor to turn the coil, Motor: 3 KW, frequency speed control
Dance arm as assistance to control stop/star rotation
B.Hydraulic Punching &Cutting device
Feeding ROLLERS, SHARE THE SAME POWER FROM THE MAIN MOTOR
Stop to Punch, Total one set of punching station
FOR PUNCHING HOLES SIZE
ONLY below one embossing mode WILL BE ABLE TO USE THE PUNCHING
Hydraulic group, Pump motor =5.5KW
C. Roll forming M/C
Feeding guide, manual adjustable with screw/hand wheel for different strip width
Gear/Sprocket driving
13+5 stages to form
(FIVE STAGES FOR THREE DIFFERENT RIBBING)
All stages for different reinforce ribs located in the roll former
Spacer change SIZE
Diameter of shaft=ф75mm
Rollers manufactured from 45# steel, Hard Chrome Coated
Main motor =7.5KW, frequency speed control
Max. Line speed of roll former: approx.12m/min
Protection Mesh Cover Above Roll-former To Avoid Hands Go Inside
D.Hydraulic Cutting M/C
Stop to cut, post cut
Total two sets of cutting blades,One is for cutting YX15-96 Profile.
Another is for cutting YX15-145 Profile
Cutting tool material: Cr12Mov, Heat treatment
E. PLC Control System
Control the quantity, drawing length & cutting length automatically.
Combined with: PLC, Touch Screen (Siemens), Inverter (SCHNEIDER), Encoder (Omron), etc
Cut-to-length tolerance≤±2.0 mm
Control voltage 24V
Product Rack Un-powered, 3 units
After-Sale Service
In correct operation & maintaining, the machine is guaranteed for one year since leaving our factory excludes the electric elements.
Installation:
If installation is needed, WE will dispatch a technician to the buyer's factory abroad to assist regulating the machine with charge free. The buyer should assist US to get the Chinese technician's visa and should pay for the roundtrip air ticket and the local accommodation.
If installation is needed, the buyer shall make the following preparation before arrival of technicians.
Terms Of Trade
1.Package & Shipment: Facility water-proof packing, Control cabinet packed in wooden packing.
2.Payment: 30%payment by T/T is required as deposit within a week since the contract signing date.70% payment by T/T is required before the machine be send out of factory.
Audited Supplier 
){kind=link}
){kind=link}