This Profile Drawing As Below Picture:
General Parameter
| 1 |
Item |
Parameters |
| 2 |
Size |
C80-250 |
| 3 |
Material |
Galvanized Steel |
| 4 |
Thickness |
2.0-4.0 mm |
| 5 |
Yield Strength |
350-400 MPa |
| 6 |
Feed Width |
According to the profile |
| 7 |
Forming speed |
Approx.25 m/min |
| 8 |
Roll Stages |
22 Stages |
| 9 |
Main Motor Power |
40 KW (Servo Motor) |
| 10 |
Hrdraulic group motor |
30 KW |
| 11 |
Shafts Diameter |
ф75/95 mm |
| 12 |
Electric Standard |
According to local voltage |
Machine Components
A. 5Ton*650mm Hydraulic Un-coiler
Hydraulic system to expand coil inner hole;Pump motor:3KW;
Frequency Inverter to regulate turn speed;Motor:3KW
Coil Inner-diameter= 470-560mm. Coil Outer-diameter Max. 1600mm;
Link-connect expanding system
Load Capacity: Max. 5 Tons; Coil Width Max. 650mm;
Hydraulic Holder on the top to hold the sheet, keep press all the working time, special design on the hydraulic group
B. Pre-Leveling Device/Pre-punching
Sheet feeding guide section with width variation
Two steps of Powered feeding rollers, driven by SERVO MOTOR <SCHNEIDER>, Servo motor power: 7.5KW
Position of Servo motor move to between pre-leveling device to pre-punching device.
The In-feed Section of the machine allows for variations in sheet width
Pre-Level Device with 5 over 4 shafts to remove the Coil-set
Special punching system, it can control by two servo motor for every punching system. The below
Hydraulic group, Pump motor =30KW
Hydraulic group with accumulator to increase pressure
C. Hydraulic Pre-cutting
stop to cut
Pre-cutting device, PLC control, purlin has bit open-up in both ends;
panel length min 2.0m.But last piece sheet have to min.3.5m
D. Feeding Table 5 meter long
E. Cold Rolling Mills
The feeding section with guide;
Gear/Sprocket driving, (20+2)-step to form
Frame stand Construction,H beam base,with leveling bolts in the base to adjust the level
Rollers manufactured from Cr12, Heat Treatment.
Shaft Diameter=Φ75/95mm, Precision Machined, heat Treatment
Sizes Changing: Movable design of one side/Dovetail slot structure
By PLC control
-setting size in PLC to reach the size requested (incl.width, flange, lip)
-setting size in PLC to reach the size requested (incl.width, flange, lip)
Main Motor=40 KW (Servo motor)
Forming speed approx. 0-25m/min
F. Hydraulic post Cutting
Stop to Cut, Post Cut
Innovative cutting system
Different cutting sizes adjustable by screw
Cutting tool material: Cr12Mov
G. PLC Control System
Control the quantity, punching position & cutting Length automatically, and setting parameters for auto web/flank size changing
Cut-to-length for post-cut,
Combined with: PLC, Touch Screen (SIEMENS ),Inverter (SCHNEIDER), Encoder (Omron), etc
Closed Loop control,
Cut-to-length tolerance≤±1 mm
Control Voltage 24V
H. Run-out Rack 6 meters, un-power
After-Sale Service
In correct operation & maintaining, the machine is guaranteed for one year since leaving our factory excludes the electric elements.
Installation:
If installation is needed, WE will dispatch a technician to the buyer's factory abroad to assist regulating the machine with charge free. The buyer should assist US to get the Chinese technician's visa and should pay for the roundtrip air ticket and the local accommodation.
If installation is needed, the buyer shall make the following preparation before arrival of technicians.
Terms Of Trade
- Package & Shipment: Facility water-proof packing, Control cabinet packed in wooden packing.
- Payment: 30%payment by T/T is required as deposit within a week since the contract signing date.70% payment by T/T is required before the machine be send out of factory.
Audited Supplier 
){kind=link}
){kind=link}